Echo PE-230 Uživatelský manuál

Power EdgerOperator's ManualMODELS PE-230Serial Number 05011201 - 05999999WARNING DANGERX75000343104/03X7502098301Read rules for safe opera

10ASSEMBLYDRIVE SHAFT/POWER HEADTools Required: 4 mm Hex WrenchParts Required: Power Head, Drive Shaft Assembly1. Loosen, the bolt (A) at engine drive

POWER EDGEROPERATOR'S MANUAL113. Bundle and secure ignition leads against engine housing with clip(F).FFRONT HANDLETools Required: Cross-Head Scr

12PRE-OPERATIONFUELFuel RequirementsGasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline knownto be good quality. Gasoline may contain up t

POWER EDGEROPERATOR'S MANUAL13OPERATIONSTARTING COLD ENGINEWARNING DANGERThe attachment will operate immediately when the engine startsand

14STARTING WARM ENGINEThe starting procedure is the same as Cold Start except DO NOT closethe choke, and do not depress throttle trigger to wide open

POWER EDGEROPERATOR'S MANUAL15OPERATING TECHNIQUES1. Before edging, water the area to soften the ground to make edgingeasier.2 Before edging, che

16MAINTENANCEYour ECHO edger is designed to provide many hours of trouble free service. Regular scheduled maintenance will helpyour edger achieve that

POWER EDGEROPERATOR'S MANUAL17AIR FILTERLevel 1.Tools required: 25 or 50 mm (1 or 2 in.) Cleaning brushParts required: 90008 REPOWERTM Air &

18SPARK PLUGLevel 2.Tools Required: T-Wrench, feeler gauge, soft metal brush.Parts Required: REPOWERTM Tune-Up Kit P/N 900741. Remove spark plug and c

POWER EDGEROPERATOR'S MANUAL191. Remove spark plug lead.2. Remove two (2) muffler cover screws and muffler cover (A).3. Remove screw and arm rest

2INTRODUCTIONWelcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job-dependability. Read and

201. Remove two (2) muffler cover screws and muffler cover (A).2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt fromentering cylinder.3

POWER EDGEROPERATOR'S MANUAL21NOTEEvery unit is run at the factory and the carburetor is set in compli-ance with emissions regulations. This carb

22BLADE REPLACEMENT/LUBRICATIONLevel 1.Tools Required: Scrench, Locking Tool, Needle Nose Pliers, 13 mmOpen End WrenchParts Required: ECHO® LUBETM 8 o

POWER EDGEROPERATOR'S MANUAL23TRAHCGNITOOHSELBUORTMELBORPENIGNEmelborPkcehCsutatSesuaCydemeRenignE-sknarc/drahstratst'nseodtratsroterubracta

24STORAGEWARNING DANGERDuring operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clearof flamm

POWER EDGEROPERATOR'S MANUAL25NOTES

26NOTES

POWER EDGEROPERATOR'S MANUAL27NOTES

DEALER?Call1-800-432-ECHOorwww.echo-usa.comCONSUMER PRODUCTSUPPORT1-800-673-15588:30 - 4:30 Mon - Fri C.S.T.ECHO, INCORPORATED400 OAKWOOD R OADLAKE Z

POWER EDGEROPERATOR'S MANUAL3SAFETYDECALSLocate these safety decals on your unit. The complete unit illustrationfound in the "DESCRIPTION&q

4INTERNATIONAL SYMBOLSSAFETY I NSTRUCTIONSPERSONAL CONDITION AND SAFETY EQUIPMENTWARNING DANGEREdger users risk injury to themselves and others

POWER EDGEROPERATOR'S MANUAL5EXTENDED OPERATION/EXTREME CONDITIONSVibration and ColdIt is believed that a condition called Raynaud’s Phenomenon,

6SAFE OPERATIONWARNING DANGERDo not operate this product indoors or in inadequately ventilatedareas. Engine exhaust contains poisonous emissions

POWER EDGEROPERATOR'S MANUAL7DESCRIPTIONThe ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging rest

81. POWER HEAD - Factory assembled. Includes the engine, clutch, fuel system, ignition system and starter.2. THROTTLE TRIGGER LOCKOUT - This lever mus

POWER EDGEROPERATOR'S MANUAL9SPECIFICATIONSMODEL -----------------------------------------------------PE-230Length ------------------------------