Echo SHRED'N'VAC ES-210 Uživatelský manuál Strana 1

SHRED 'N' VAC®Operator's Manual MODEL ES-210 X75300297311/09X7531135903 WARNING Read rules for safe operation and al

10DE 5. Align grooves in discharge elbow with pegs on blower, and slide elbow (D) on to blower. Turn elbow counterclockwise to lock in place. Elbo

11Sh r e d 'N' Va c® op e r a T o r 's ma n u a lHandling Fuel DANGERFuel is VERY ammable. Use extreme care when mixing, storin

12ABCDEs T a r T I n g C o l d e n g I n e 1. Stop Switch Move stop sw

13Sh r e d 'N' Va c® op e r a T o r 's ma n u a ls T a r T I n g w a r m e n g I n eThe starting procedure is the same as Cold Start

14Read the Safety Section carefully.IMPORTANT To avoid engine damage due to over-revving, do not block blower pipe. 1. Use only during appropriate

15Sh r e d 'N' Va c® op e r a T o r 's ma n u a ls h r e d ‘n’ v a C ® o p e r a T I o n WARNING Flying debris hazard. Never o

16Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your blower achieve that goal. I

17Sh r e d 'N' Va c® op e r a T o r 's ma n u a lf u e l f I l T e rLevel 1.Tools required: 200-250 mm (8-10 in.) length of wire wi

180.65 mm(0.026 in.)C o o l I n g s y s T e mLevel 2.Tools required: 25-50 mm (1-2 in.) cleaning brush, 3 mm hex wrench, cross head screwdriverParts

19Sh r e d 'N' Va c® op e r a T o r 's ma n u a le x h a u s T s y s T e mSpark Arrestor ScreenLevel 2.Tools required: Cross Head

2Ta b l e o f Co n T e n T sIntroduction ... 2 - The operator’s Manual ...

20ABExhaust Port CleaningLevel 2.Tools required: 4 mm Hex Wrench., Wood or plastic scraperParts Required: As needed: Heat Shield1. Remove spar

21Sh r e d 'N' Va c® op e r a T o r 's ma n u a ls h r e d d e r b l a d eLevel 1. WARNINGNever remove vacuum tube or open fan gu

22C a r b u r e T o r a d j u s T m e n TEngine Break-InNew engines must be operated a minimum duration of two tanks of fuel break-in before carburet

23Sh r e d 'N' Va c® op e r a T o r 's ma n u a lTr o u b l e s h o o T I n g DANGERFuel vapors are extremely ammable and may cau

24sT o r a g e WARNINGDuring operation the mufer or catalytic mufer and surrounding cover become hot. Always keep exhaust area clear of ammable

25Sh r e d 'N' Va c® op e r a T o r 's ma n u a lsp e C I f I C a T I o n sMODEL ----------------------------------------------------

26wa r r a n T y sT a T e m e n T sECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010ECHO'S RESPONSIBILITYE

27Sh r e d 'N' Va c® op e r a T o r 's ma n u a lPURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES

28 ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENTFOR ECHO AND SHINDAIWA BRANDSThe Environmental Protection Agency (EPA) and the California Air

29Sh r e d 'N' Va c® op e r a T o r 's ma n u a ln o T e s

3Sh r e d 'N' Va c® op e r a T o r 's ma n u a lI n T e r n a T I o n a l s y m b o l sSymbol description/applicationSymbol form/shap

30n o T e s

31Sh r e d 'N' Va c® op e r a T o r 's ma n u a ln o T e s

ECHO, INCORPORATED400 Oakwood RoadLake Zurich, IL 60047-1564www.echo-usa.comConsumer produCTsupporT1-800-673-15588:30 - 4:30 mo n - fr I C.s.T.P087

4Physical Condition Your judgment and physical dexterity may not be good: • if you are tired or sick, •

5Sh r e d 'N' Va c® op e r a T o r 's ma n u a l DANGERDo not operate this product indoors or in inadequately ventilated areas. En

6em I s s I o n Co n T r o l (e x h a u s T & e v a p o r a T I v e )EPA 2010 and Later and/or C.A.R.B. TIER IIIThe emission control system for

7Sh r e d 'N' Va c® op e r a T o r 's ma n u a lLocate these safety decals on your unit. Make sure the decals are legible and that yo

8 1. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop. 2. THROTTLE TRIGGER - Sp

9Sh r e d 'N' Va c® op e r a T o r 's ma n u a lAas s e m b l yRequired Tools: Screwdriver WARNINGNever perform maintenance or as